10.0.0.1 Login Admin

Your 10.0.0.1 login leads to the settings page of Xfinity gateways in the US and Rogers Xfinity gateways in Canada. Sign in with the username admin. On an Xfinity XB6, XB7, XB8 or XB10, switch on Admin Tool access in the Xfinity app first and use the password you make there. XB2, XB3 and Rogers units take the code on the bottom label. Typed 10.0.0.0.1? Drop one zero.

If your router uses 10.0.0.1, the button above opens its login page. If nothing loads, your router uses a different address; see how to read your router’s real address.

Who uses 10.0.0.1

Gateway	ISP, country	Address	Password comes from	Source
Xfinity XB6, XB7, XB8, XB10	Xfinity, US	http://10.0.0.1	The Xfinity app, when you allow Admin Tool access; the sticker if access was allowed before February 2026	Xfinity Admin Tool access
Xfinity XB2, XB3	Xfinity, US	http://10.0.0.1	Sticker on the bottom	Xfinity Admin Tool Wi-Fi change
Rogers Xfinity Gateway Gen 1 (XB6), Gen 2 (XB7), Gen 3 (XB8)	Rogers, Canada	https://10.0.0.1	Unique code on the bottom label, replaced at first sign-in	Rogers gateway help

The username is admin on all three. Older login lists add Cisco, Technicolor and D-Link with guessed pairs; no maker page backs them, so go by your own label.

Which Xfinity gateway do you have

The sticker shows a model number, not the XB name. Match it here, using Xfinity’s gateway model list:

Model number on the label	Xfinity name	Admin password
TC8706C, TG852G, TG862G, TC8305C	XB2	Sticker
DPC3939, DPC3941T, TC8717, TG1682G	XB3	Sticker
TG3482G, CGM4140COM	XB6	Made in the app, or the sticker if allowed before February 2026
CGM4331COM, TG4482A	XB7	Made in the app, or the sticker if allowed before February 2026
CGM4981COM	XB8	Made in the app, or the sticker if allowed before February 2026
SG417DBCT, CGM601TCOM, CGM601TCM	XB10	Made in the app, or the sticker if allowed before February 2026
CWA438TCOM	XB9	Not named on the toggle page; look for the toggle in the app

No sticker in reach? The Devices page of your Xfinity account and the Xfinity app show the model too.

Why is my default gateway 10.0.0.1?

Your phone lists 10.0.0.1 as the gateway when the box handing out addresses keeps that number for itself. Xfinity and Rogers gateways ship that way. A router, mesh kit, office or hotel network can also be put on the 10.x range by whoever installed it.

We found no ISP page in Kenya, Tanzania, South Africa, Nigeria, India or Indonesia that sets 10.0.0.1 as the default. Check what your own device reports first:

• Phone: open Wi-Fi settings, tap the network you are on and read the Router or Gateway line.
• Windows: run ipconfig in Command Prompt and read Default Gateway.

Type whatever number shows there. The router login hub for every address picks up from that number.

Your gateway shows a different address

Searching “10.0.0.1 huawei” or “10.0.0.1 tp link”? No Huawei or TP-Link page puts their home routers at this address. Start from Huawei router logins by model or TP-Link login steps.

10.0.0.1 admin login on Xfinity

The toggle is offered on the XB6, XB7, XB8 and XB10. The Wireless Gateway 1, Wireless Gateway 2 and XB3 lack it, and Xfinity asks owners of those older units to contact it about an update.

Which admin password to type

Your situation	Password that works
XB6 to XB10, access first allowed after February 2026	The one typed on the app’s new password screen
XB6 to XB10, access allowed before February 2026	The sticker default may still be accepted
XB2 or XB3	The sticker under the gateway
Any Xfinity unit after a factory reset	The label password, unless the app asks for a new one when you allow access again

The pair admin and password that many sites print appears on no current Xfinity page.

Reset Xfinity router admin password when locked out

Xfinity publishes no help page for a forgotten Admin Tool password. In two community forum threads, Xfinity staff gave the same answer: a factory reset puts the login back to admin with the password printed on the bottom label.

Change Wi-Fi password, port forwarding and pause settings

Many settings that older guides place at 10.0.0.1 now live in the app:

Task	Where to do it	Source
Wi-Fi name or key, Xfinity	XB2 or XB3: 10.0.0.1, Gateway > Connection > Wi-Fi, Edit under Private Wi-Fi Network, then Save Settings. XB6 or newer, or any home with Xfinity WiFi Extenders: the Xfinity app only	Xfinity Wi-Fi change
Wi-Fi name or key, Rogers	Rogers Xfinity app, Connect > See Network > Edit	Rogers sign-in help
Port forwarding, Xfinity	Xfinity app, WiFi > View WiFi equipment > Advanced Settings > Port forwarding > Add Port Forward	Xfinity port forwarding
Port forwarding, Rogers	Rogers Xfinity app, same path	Rogers port forwarding
Pause a device, Xfinity	Xfinity app Parental Controls: Pause, Downtime, Active Time Limits	Xfinity parental controls

Port forwarding only lists devices on IPv4 that get their address by DHCP, so a device with a static IP or on IPv6 may be missing. A phone that uses a private Wi-Fi address can break its rule; Xfinity says to delete the rule and add it again.

Rogers warns on its pause help that a paused device can still go online with cellular data or another Wi-Fi network.

The Wi-Fi key that phones type to join and the Admin Tool password are separate; changing one leaves the other as it was. Other makers’ routers are covered in Wi-Fi password steps for any router.

Xfinity gateway Bridge Mode at 10.0.0.1

Bridge Mode stops the gateway acting as a router so your own router can take over, while its modem part keeps running. Xfinity’s Bridge Mode article gives the steps:

Before you enable it, know the limits:

• The gateway’s private Wi-Fi network goes off.
• Only one device connects to the gateway, through an Ethernet port.
• It cannot be switched on while Xfinity WiFi Extenders are active.
• To switch it off again with Disable, the device you use must be on an Ethernet cable.

Bridge Mode switch missing on the gateway

10.0.0.1 login on Rogers gateways

Rogers uses the same address on its Gen 1 (XB6), Gen 2 (XB7) and Gen 3 (XB8) gateways, but its help page names only the secure form, https://10.0.0.1. Join your home Wi-Fi, switch mobile data off, type that in the address bar and sign in with admin and the unique code on the bottom of the gateway. On the first sign-in Rogers asks you to create a new admin password. To change it later, go to Troubleshooting > Change Password and save.

Expect a browser security warning first; on this gateway it is normal.

On Firefox, choose Advanced, then Accept the Risk and Continue. The Rogers Xfinity app accepts both MyRogers and MyRogers (Shaw) usernames.

Restart or reset an Xfinity or Rogers gateway

A restart keeps every setting. A factory reset does not.

• Xfinity restart: in the app, tap the WiFi icon, then Troubleshoot, then Restart your Gateway. Allow up to 12 minutes; the home network is down meanwhile. If that fails, Xfinity’s gateway restart article says to unplug the power for one minute.
• Rogers restart: unplug the gateway for 30 seconds, then plug it in.

For Rogers, pick the lightest reset that solves the problem:

Choice or model	What to do	What is lost
Restore WiFi Settings	Troubleshooting > Reset/Restore Gateway on the admin page	Only the Wi-Fi settings
Restore Factory Settings	Same menu	Everything; set the gateway up again in the Rogers Xfinity app
Gen 1 button	Hold Reset until the light turns green again	Everything
Gen 2 and Gen 3 button	Hold WPS for at least 30 seconds, then let go	Everything
Gen 4 button	Hold Reset 15 to 30 seconds, let go when the light flashes green	Everything

The rows come from Rogers’s restart and reset help; the app set-up step is on its gateway page. For routers from other makers, see factory reset steps for other routers.

10.0.0.1 Piso WiFi and PLDT

Piso WiFi is the coin-fed Wi-Fi vendo found across the Philippines. Its portal, timer, pause button and admin dashboard belong to the operator who set up the machine. AdoPiSoft is one vendo system: its product site publishes no portal address or admin login. No LPB vendo page with a login turned up either.

If paid time seems to vanish when your phone reconnects, ask the operator first. Android 10 and later, and iPhones, join each network with a private Wi-Fi address by default, and no vendo maker says whether time is tied to it. On an iPhone with iOS 18 or later, open Settings > Wi-Fi, tap the More Info button beside the network, then Private Wi-Fi Address. Choose Off, Fixed or Rotating; Rotating changes every two weeks, per Apple’s private address page.

No maker or ISP page puts a PLDT Home modem at 10.0.0.1. Its sign-in details are on the modem’s label, and the gateway line on your phone shows the address it really uses.

10.0.0.0.1 and other typo forms

An IPv4 address is four numbers joined by three dots, so a typo form such as 10.0.0.0.1, with five numbers, makes the browser run a web search instead. The same happens with:

• 10.0 0.1 (a space where a dot belongs)
• 10.o.o.1 (the letter o in place of zero)
• https://10.10.0.0.1 and 10001
• www.10.0.0.1

10.0.0.1 itself is a valid private address. RFC 1918 reserves 10.0.0.0 to 10.255.255.255 for private networks, so it only answers from inside the home network that owns it.

10.0.0.1 login not working

The page does not load on an XB6 or newer

Admin Tool access is probably off. Allow it in the Xfinity app under WiFi, View WiFi equipment, Advanced settings, and make sure you are on your home network.

Nothing loads on public Wi-Fi or mobile data

The xfinitywifi hotspot and mobile data cannot reach your gateway. Join your home Wi-Fi or use an Ethernet cable.

The pair admin and password is refused

It is not a current Xfinity default. Use the password made in the app, or the sticker password if access was allowed before February 2026.

No switch next to Bridge Mode

A fault owners reported in early 2026. Unplug the gateway for 30 seconds, then follow the Bridge Mode note above if it stays missing.

None of these fit

Your router is probably not on 10.0.0.1. Read the gateway line on your phone or run ipconfig, and open that address.

A stuck browser cache or a VPN can also block the page; those causes are covered under when a router admin page refuses to load.

Conclusion

Xfinity and Rogers gateways answer at 10.0.0.1 with the username admin. The password comes from the Xfinity app or from the label, depending on the model and on when access was allowed. Everyone else should check the gateway line and pick the right page from the full list of router IP addresses.